Antics Models, Diecast, Radio Control and Model Railways
  1. Antics Online Model Railways Power & Electrics Electric Point Control

Peco PL-10WE Point Motor Low Current Extended Pin

Peco PL-10WE Point Motor Low Current Extended Pin

A new point motor type from Peco incorporating the extended operating pin, allowing the motor to be mounted to the underside of baseboards, with the low current solenoid design.
These motors have a lower power consumption, designed with DCC systems in mind allowing these motors to be controlled by point/accessory decoders.
£8.85
MRP £8.85

This product is no longer available.
(Product Ref 64418)
Have a question about this product? Let us know
Contact us
A 9.5mm or 3/8in hole below the point tie bar is recommended.
Have a question about this product? Let us know
Contact us
Related Products
A set of five mounting plates with attachment slots for PL10 point motors. This allows the motor to be mounted beneath the baseboard, avoiding the need to make a large hole to accommodate the motor directly beneath the point.
Peco 5 Mounting Plates for PL10 PL-9
£4.75
Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.Pack of 2 looms.
Peco Wiring Loom for Peco Point Motors PL-34
£7.20
A pack of 20 self-adhesive cable clips, ideal for keeping wiring under control under layouts and inside larger models.
Peco Self-Adhesive Cable Clips Pack of 20 PL-37
£4.75
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Red Lever PL-26R
£9.75
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch White Lever PL-26W
£9.75
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Black Lever PL-26B
£9.75
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Yellow Lever PL-26Y
£9.75
Control switch and wiring harness for connection to Peco point motors. Switch and point motor harness are supplied complete wiith connectors for the EZE-Wire system, allowing extensions to be added between the switch and motor to reach the point motor location. Heat-shrink tubing is supplied to protect and insulate joints.EZE-Wire - Plug and Play layout wiring from Expo.The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
Expo EZE-Wire Point Switch with Peco Point Motor Harness 28070
£4.99