Electric Point Control

Point motors, control switches and wiring
Hornby Surface Mount Point Motor R8243
Designed to fit alongside the current range of Hornby points this motor allows points to be converted to remote operation quickly and easily, without needing holes drilled in the baseboard.
£13.25
Warehouse: 4
Bristol: 1, Cardiff: 3, Gloucester: 4, Plymouth: 1, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 63272)
Cookies are disabled.
To place an order please call 01453 377030
This point motor is designed to mount alongside a point, avoiding the need to cut a hole into the baseboard to fit a motor below each point.
Fits directly to OO/HO points. Can be used with N points but due to the lower height track check that the point motor unit is clear of the passing trains.
£11.25
Warehouse: 9+
Bristol: 6, Cardiff: 2, Gloucester: 5, Plymouth: 7, Stroud: 4
Fast delivery from Warehouse.
(Product Ref 64095)
Cookies are disabled.
To place an order please call 01453 377030
TwistLock is still a basic electric solenoid motor, for operating turnouts powered by a normal 16vDC supply (can take up to 3 amps), is fully compatible with all PECO turnouts up to O gauge and many other proprietary brands to. The mounting of the point motor is greatly simplified by the Twistlock system and cabling is connected, reducing the need for soldering of wires to the terminals. PL-1001 supplied with DPDT switch for crossing polarity switching etc.
£22.25
Warehouse: 6
Gloucester: 2, Plymouth: 1
Fast delivery from Warehouse.
(Product Ref 111508)
Cookies are disabled.
To place an order please call 01453 377030
The PL10E point motor is fitted with a long point operating pin, ideal for mounting beneath baseboards. A small 10mm (3/8in) hole through the baseboard is required, located directly beneath the operating pin attachment location on the point. The pin will then reach through the board and locate into the operating pin attachment hole of the point. The pin can then be trimmed to length with a good side or track cutter tool. Peco strongly recommend that the PL10E be used in conjunction with a PL-9 Mounting Plate, fitted directly to the base board underneath the point. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor.
£8.95
Warehouse: 9+
Bristol: 6, Cardiff: 6, Gloucester: 4, Plymouth: 6, Stroud: 5
Fast delivery from Warehouse.
(Product Ref 31749)
Cookies are disabled.
To place an order please call 01453 377030

5m of Red/Green/Black tripled wire. Ideal for model railway point motor use and helpful when trying to keep wiring tidy.

Each wire includes 14 strands of 0.15mm diameter wire.

£6.95
Warehouse: 1
Bristol: 1, Gloucester: 2, Plymouth: 2, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 109368)
Cookies are disabled.
To place an order please call 01453 377030
2 Adaptor Bases are included, with optional extension arms, to enable PL-10 Turnout Motors to be mounted on the surface of the baseboard. This unit relies on the over centre spring in the turnout to keep the blades against the stock rail.
£2.95
Warehouse: 9+
Gloucester: 7, Plymouth: 2
Fast delivery from Warehouse.
(Product Ref 89692)
Cookies are disabled.
To place an order please call 01453 377030

10m of Red/Green/Black tripled wire. Ideal for model railway point motor use and helpful when trying to keep wiring tidy.

Each wire includes 14 strands of 0.15mm diameter wire.

£10.75
Warehouse: 4
Bristol: 1, Cardiff: 1, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 116117)
Cookies are disabled.
To place an order please call 01453 377030

25m drum of Red/Black/Red tripled wire. Ideal for model railway point motor use and helpful when trying to keep wiring tidy.

£29.95
Warehouse: 2
Fast delivery from Warehouse.
(Product Ref 123369)
Cookies are disabled.
To place an order please call 01453 377030
This unit enables a PL-10 Turnout Motor to be mounted on the surface of the baseboard, an optional extension arm is also included. A removable over centre spring is fitted, useful for turnouts which do not have this feature.
£4.50
Warehouse: 9+
Bristol: 9+, Cardiff: 6, Gloucester: 5, Plymouth: 4, Stroud: 5
Fast delivery from Warehouse.
(Product Ref 31751)
Cookies are disabled.
To place an order please call 01453 377030
Attaches directly to the PL-10 family of Turnout Motors with contact adhesive. This single pole switch can control frog polarity, ground signals etc. PL-31 Spade Connectors can be used to attach wires to these units without the need for soldering.
£5.25
Warehouse: 9+
Bristol: 3, Cardiff: 6, Gloucester: 3, Plymouth: 5, Stroud: 5
Fast delivery from Warehouse.
(Product Ref 31752)
Cookies are disabled.
To place an order please call 01453 377030
This fits directly to the PL-10 family of Turnout Motors. The 2 single pole changeover switches can be used to control polarity, route selection diagrams, or 2 aspect colour light signalling etc. Rated 16v 2amps (continuous) or 2.5amps (momentary).
£12.50
Warehouse: 5
Bristol: 5, Gloucester: 2, Plymouth: 2, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 31753)
Cookies are disabled.
To place an order please call 01453 377030
These useful switches are similar to those used in the PL-15 twin microswitch kit. Rated at 16 volts with 2amp continuous use or 2.5 amps passing contact. Two per pack.
£7.75
Warehouse: 4
Bristol: 2, Gloucester: 5, Plymouth: 2, Stroud: 2
Fast delivery from Warehouse.
(Product Ref 31773)
Cookies are disabled.
To place an order please call 01453 377030
Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary).
Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip.
£7.75
Warehouse: 6
Bristol: 4, Cardiff: 4, Gloucester: 4, Plymouth: 4, Stroud: 2
Fast delivery from Warehouse.
(Product Ref 31774)
Cookies are disabled.
To place an order please call 01453 377030
Gaugemaster Seep Point Motor c/w Switch PM1
A reliable solenoid type point motor equiped with an internal switch. Ideal for use with electrofrog points when polarity switching is required.
£7.25
Warehouse: 7
Gloucester: 3, Plymouth: 1
Fast delivery from Warehouse.
(Product Ref 42823)
Cookies are disabled.
To place an order please call 01453 377030
Gaugemaster Seep Point Motor PM2
Seep Point Motors have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-2 is a standard point motor with no changeover switch. Drive rod 41mm long.
£5.50
Warehouse: 1
Fast delivery from Warehouse.
(Product Ref 102572)
Cookies are disabled.
To place an order please call 01453 377030
A reliable solenoid type point motor equiped with a self-latching mechanism. Ideal for use with points not having their own latching mechanism to ensure that the points are held closed firmly.
£6.75
Warehouse: 6
Fast delivery from Warehouse.
(Product Ref 42824)
Cookies are disabled.
To place an order please call 01453 377030

Three position on/off/on biased (momentary action, switch returns to off when released) miniature toggle switch rated at 5amp/28volt DC. Ideal for operating solenoid point motors on model railways.

Size 9mm high x 13mm wide x 7mm deep. Requires 6.35mm (1/4in) hole for fitting.

£11.95
Warehouse: 4
Bristol: 1, Gloucester: 2, Plymouth: 2, Stroud: 3
Fast delivery from Warehouse.
(Product Ref 3243)
Cookies are disabled.
To place an order please call 01453 377030

Three position on/off/on biased (momentary action, switch returns to off when released) miniature toggle switch rated at 5amp/28volt DC. Ideal for operating solenoid point motors on model railways.

Size 9mm high x 13mm wide x 11.5mm deep. Requires 6.35mm (1/4in) hole for fitting.

£10.00
Warehouse: 3
Bristol: 1, Cardiff: 1, Gloucester: 3, Plymouth: 3, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 3244)
Cookies are disabled.
To place an order please call 01453 377030
A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.
£6.25
Warehouse: 1
Gloucester: 3, Stroud: 2
Fast delivery from Warehouse.
(Product Ref 31754)
Cookies are disabled.
To place an order please call 01453 377030
A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.
£5.50
Warehouse: 1
Bristol: 3, Gloucester: 3
Fast delivery from Warehouse.
(Product Ref 31755)
Cookies are disabled.
To place an order please call 01453 377030
This plugs directly into a ready made recess on the 0 gauge Double Slip SL-E790BH to house a PL-33 Microswitch to operate the polarity switching.
£5.75
Warehouse: 8
Bristol: 3, Plymouth: 1
Fast delivery from Warehouse.
(Product Ref 105920)
Cookies are disabled.
To place an order please call 01453 377030
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
£9.50
Warehouse: 6
Bristol: 3, Cardiff: 6, Gloucester: 8, Stroud: 5
Fast delivery from Warehouse.
(Product Ref 31764)
Cookies are disabled.
To place an order please call 01453 377030
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
£9.50
Warehouse: 9+
Bristol: 5, Cardiff: 6, Gloucester: 6, Plymouth: 7, Stroud: 3
Fast delivery from Warehouse.
(Product Ref 31762)
Cookies are disabled.
To place an order please call 01453 377030
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
£9.50
Warehouse: 8
Plymouth: 1, Stroud: 3
Fast delivery from Warehouse.
(Product Ref 31763)
Cookies are disabled.
To place an order please call 01453 377030
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
£9.50
Warehouse: 5
Gloucester: 1
Fast delivery from Warehouse.
(Product Ref 31765)
Cookies are disabled.
To place an order please call 01453 377030
A six bay console to take PL-22, 23 or 26 switches. Suitable for use in banks.
£6.50
Warehouse: 2
Gloucester: 1, Stroud: 2
Fast delivery from Warehouse.
(Product Ref 31766)
Cookies are disabled.
To place an order please call 01453 377030
Enables switches to be connected without any need for soldering. Power is supplied through the fitted leads and each switch is automatically connected when fitted. Simply push the button on the front to open the holes, and feed in the bare wires from the turnout motor - no soldering or other fixing required. The PL-51 allows the PL-50 module to be extended to any size required.
£26.95
Warehouse: 1
Gloucester: 1, Plymouth: 1
Fast delivery from Warehouse.
(Product Ref 78598)
Cookies are disabled.
To place an order please call 01453 377030
Allows the PL-50 Switch Module to be extended to any size required.
£9.50
Warehouse: 7
Bristol: 6, Gloucester: 1, Plymouth: 2
Fast delivery from Warehouse.
(Product Ref 78599)
Cookies are disabled.
To place an order please call 01453 377030

Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.

Pack of 2 looms.

£6.95
Warehouse: 6
Bristol: 3, Gloucester: 5
Fast delivery from Warehouse.
(Product Ref 74801)
Cookies are disabled.
To place an order please call 01453 377030
Antics recommended for ease of installation
The Peco capacitor discharge unit is supplied in a neat plastic box with quick clamp type connectors, ready for installation without needing further protection.
The capacitors provide sufficient instantaneous energy to positively throw point motors.
£24.95
Warehouse: 2
Gloucester: 2, Plymouth: 1
Fast delivery from Warehouse.
(Product Ref 70593)
Cookies are disabled.
To place an order please call 01453 377030

Control switch and wiring harness for connection to Peco point motors. Switch and point motor harness are supplied complete wiith connectors for the EZE-Wire system, allowing extensions to be added between the switch and motor to reach the point motor location. Heat-shrink tubing is supplied to protect and insulate joints.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.

£4.99
Warehouse: 2
Plymouth: 3
Fast delivery from Warehouse.
(Product Ref 3270)
Cookies are disabled.
To place an order please call 01453 377030
Black extension wire for the Expo EZE-Wire layout wiring system.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
£2.00
Warehouse: 1
Fast delivery from Warehouse.
(Product Ref 795)
Cookies are disabled.
To place an order please call 01453 377030
Blue extension wire for the Expo EZE-Wire layout wiring system.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
£2.00
Warehouse: 2
Fast delivery from Warehouse.
(Product Ref 2040)
Cookies are disabled.
To place an order please call 01453 377030
Green extension wire for the Expo EZE-Wire layout wiring system.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
£2.00
Warehouse: 3
Fast delivery from Warehouse.
(Product Ref 2749)
Cookies are disabled.
To place an order please call 01453 377030
Red extension wire for the Expo EZE-Wire layout wiring system.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
£2.00
Warehouse: 2
Fast delivery from Warehouse.
(Product Ref 2023)
Cookies are disabled.
To place an order please call 01453 377030
Enables an LGB(TM) motor to be fitted to a Peco G45 Turnout.
£6.95
Warehouse: 9+
Bristol: 1
Fast delivery from Warehouse.
(Product Ref 31746)
Cookies are disabled.
To place an order please call 01453 377030
Allows adjacent switches in the PL-27 Switch Console and PL-50/51 Switch Module Unit to be ganged together and operated simultaneously.
£4.25
Warehouse: 9+
Bristol: 7, Gloucester: 1, Plymouth: 1, Stroud: 3
Fast delivery from Warehouse.
(Product Ref 31760)
Cookies are disabled.
To place an order please call 01453 377030
The Smart Switch provides an excellent flexible solution to remote point control using a programmable four-switch control board with outputs for highly controllable servo motor machines. The servo motors can be installed under or above the baseboard with the drive arranged in several ways to activate points, semaphore signals or level crossing gates.
The board also provides for feedback outputs to power indicator LEDs on a control panel. Points are activated from a control panel using change-over toggle switches (supplied) or the board can be programmed to accept a signal from a push-to-make button switch. Due to the low currents needed for these command signals multi-way computer ribbon cabling can be used to keep wire runs tidy for connection to centralised control panels. Additional servo extension leads are readily available, these are the same leads as used by RC modellers.
For use with insulated frog or power-routing points. For live frog points requiring power feeds a SmartFrog polarity switching unit will soon become available.
£80.00
MRP £89.95
Warehouse: 1
Fast delivery from Warehouse.
(Product Ref 86116)
Cookies are disabled.
To place an order please call 01453 377030
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Control Board will facilitate the control of up to 4 Servos. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
£15.95
Warehouse: 4
Fast delivery from Warehouse.
(Product Ref 92333)
Cookies are disabled.
To place an order please call 01453 377030
3-way snap-closed connectors suitable for connecting model railway track power and point motor circuits as an alternative to soldering connections.
£12.95
Warehouse: 5
Cardiff: 1, Gloucester: 1, Plymouth: 1, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 56816)
Cookies are disabled.
To place an order please call 01453 377030
A pack of 6x red/green chrome mount pre-wired bi-colour 3mm LEDs.
3mm LED in 1/4? chromed brass mount. Leads 300mm, resistor already added, safe voltage range 12 to 15 volts DC.
£8.95
Warehouse: 2
Bristol: 1, Gloucester: 1, Plymouth: 1, Stroud: 1
Fast delivery from Warehouse.
(Product Ref 116023)
Cookies are disabled.
To place an order please call 01453 377030
Resistors for use with the PL-30 Red and Green LED's fed from a 12volt DC supply.
£4.50
Warehouse: 2
Fast delivery from Warehouse.
(Product Ref 105921)
Cookies are disabled.
To place an order please call 01453 377030
These can be used directly from terminals on the Smartswitch (TM) Control Board (PLS-120) and Smartfrog (PLS-130) to show route selection. They can also be powered via a 12v DC supply if the PL-29 Resistors are included in the circuit.
£5.50
Warehouse: 1
Gloucester: 1
Fast delivery from Warehouse.
(Product Ref 90572)
Cookies are disabled.
To place an order please call 01453 377030
Gaugemaster Seep Universal Solenoid Point Motor with Extension Rod GMC-PM10
£8.50
Warehouse: 5
Fast delivery from Warehouse.
(Product Ref 30329)
Cookies are disabled.
To place an order please call 01453 377030
For fitting point motors above baseboard
£8.75

Stroud: 1
Delivery from stores takes a few days longer!
(Product Ref 505)
Cookies are disabled.
To place an order please call 01453 377030
This motor attaches directly to the underside of the point to ensure positive and reliable operation. Requires a 40 x 25mm hole in the baseboard to accommodate the motor. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice.
Use only a pulse as applying a constant current would burn out the motor.
£8.95

Bristol: 8, Plymouth: 5
Delivery from stores takes a few days longer!
(Product Ref 31748)
Cookies are disabled.
To place an order please call 01453 377030
TwistLock is still a basic electric solenoid motor, for operating turnouts powered by a normal 16vDC supply (can take up to 3 amps), is fully compatible with all PECO turnouts up to O gauge and many other proprietary brands to. The mounting of the point motor is greatly simplified by the Twistlock system and cabling is connected, reducing the need for soldering of wires to the terminals.
£15.75

Plymouth: 1, Stroud: 2
Delivery from stores takes a few days longer!
(Product Ref 111507)
Cookies are disabled.
To place an order please call 01453 377030
Twistlock mounting DPDT accessory switch for mounting on Peco Twistlock point motors.
£9.95

Gloucester: 2
Delivery from stores takes a few days longer!
(Product Ref 111509)
Cookies are disabled.
To place an order please call 01453 377030

This point motor is designed to operate with the lower current available from some European transformers or with DCC systems*. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers. If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor.

* Although the initial amperage from DCC systems is very high, say 10 amps, the final amps available to accessories such as point motors is very low, once the current has passed through the booster units used in DCC systems.

£8.85

Plymouth: 1
Delivery from stores takes a few days longer!
(Product Ref 31750)
Cookies are disabled.
To place an order please call 01453 377030
A set of five mounting plates with attachment slots for PL10 point motors. This allows the motor to be mounted beneath the baseboard, avoiding the need to make a large hole to accommodate the motor directly beneath the point.
£4.50

Bristol: 3, Gloucester: 3, Plymouth: 1, Stroud: 4
Delivery from stores takes a few days longer!
(Product Ref 31747)
Cookies are disabled.
To place an order please call 01453 377030
DCC Concepts Cobalt Slow Action Point Motor H-DCP-CB1
Cobalt is a high quality DC motor driven actuator created to be the best product available for turnout or signal control in any modelling scale from N to O.
£17.95

Plymouth: 1
Delivery from stores takes a few days longer!
(Product Ref 4197)
Cookies are disabled.
To place an order please call 01453 377030
Hornby Passing Contact Lever Switch for Points R044
For operating point motors - passing contact to give a single pulse.
£14.49

Cardiff: 2
Delivery from stores takes a few days longer!
(Product Ref 6431)
Cookies are disabled.
To place an order please call 01453 377030
Use these when creating a diagrammatic control panel to clip fit PL-26 Passing Contact Switches, PL-22 On/Off Switches and PL-23 On/On Switches in the required place.
£4.25

Bristol: 5, Gloucester: 2
Delivery from stores takes a few days longer!
(Product Ref 31767)
Cookies are disabled.
To place an order please call 01453 377030
Push on Terminal Connectors and shrouds. These connectors make modification and fault finding so much easier than soldered wiring. Use them to connect the PL-38 Wire to PL-26 Passing Contact Switches, PL-22 On/Off Switches, PL-23 On/On Switches, and PL-34 Wiring Looms to PL-26 Passing Contact Switches. They can also be used when connecting wires to other items, for example, PL-13 Accessory Switches, PL-15 Twin Microswitches, PL-10 Turnout Motors, and PL-32 and 33 Microswitches.
£4.25

Bristol: 2, Cardiff: 6, Gloucester: 6, Plymouth: 1
Delivery from stores takes a few days longer!
(Product Ref 31772)
Cookies are disabled.
To place an order please call 01453 377030

Pack of 5 general purpose surface mount point motors.suitable for leading UK brands of track.
Supplied complete with wiring harnesses with reversible connectors and fixing screws.

£50.00
Warehouse: 1
Must be ordered - delivery as soon as possible.
(Product Ref 77805)
Cookies are disabled.
To place an order please call 01453 377030
Powerful solenoid point motor, may be mounted above or below baseboard, powered from 16v AC supply. Requires Passing Contact Lever Switch (R044)
£12.65

Must be ordered - delivery as soon as possible.
(Product Ref 499)
Cookies are disabled.
To place an order please call 01453 377030
DCC Concepts Cobalt Ip Digital Point Motor DCP-CBDIP
£24.99

Must be ordered - delivery as soon as possible.
(Product Ref 46330)
Cookies are disabled.
To place an order please call 01453 377030
Gaugemaster Model CDU - Capacitor Discharge Unit CDU
A Capacitor Discharge Unit (CDU) provides a reserve of charge to ensure that a good voltage is available to throw point motors. Especially useful when several motors are thrown by one lever, setting cross-overs for example.
The unit stores up power in capacitors and when a point motor is actuated, discharges in one big punch giving the point motor a firm and positive switching action. Connected to points via switches or probe and studs. Prevents burnt out motors.
£17.50

Must be ordered - delivery as soon as possible.
(Product Ref 33977)
Cookies are disabled.
To place an order please call 01453 377030
Expo EZE-Wire Point Switch with Hornby Point Motor Harness 28071
Control switch and wiring harness and 'chocolate-block' terminal block for connection to Hornby point motors. Switch and point motor harness are supplied complete wiith connectors for the EZE-Wire system, allowing extensions to be added between the switch and motor to reach the point motor location. Heat-shrink tubing is supplied to protect and insulate joints.

EZE-Wire - Plug and Play layout wiring from Expo.
The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
£3.95

Must be ordered - delivery as soon as possible.
(Product Ref 29993)
Cookies are disabled.
To place an order please call 01453 377030

The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Control Board will facilitate the control of up to 4 Servos. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.

£37.00
MRP £40.95

Must be ordered - delivery as soon as possible.
(Product Ref 86251)
Cookies are disabled.
To place an order please call 01453 377030
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Control Board will facilitate the control of up to 4 Servos. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
£21.25

Must be ordered - delivery as soon as possible.
(Product Ref 94819)
Cookies are disabled.
To place an order please call 01453 377030
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Stationary Decoder provides an interface between a Smartswitch Control Board and a DCC control system to enable the operation of turnouts, semaphore signals, crossing gates etc through a DCC controller. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
£21.50

Must be ordered - delivery as soon as possible.
(Product Ref 92336)
Cookies are disabled.
To place an order please call 01453 377030
The Smartswitch(TM) system can be used to operate turnouts, semaphore signals, level crossing gates and barriers and other moving features. This Extension cable allows a servo to be located up to a metre further away from the Control Board. Watch the videos to see the potential uses and ease of installation of this system and see our Shows You How booklet No. 24 Operating Points and Signals.
£7.50

Must be ordered - delivery as soon as possible.
(Product Ref 8917)
Cookies are disabled.
To place an order please call 01453 377030

One Cobalt-S Signal Box Lever including all installation accessories.

Cobalt-S Levers bring a sense of reality to the control of model railways. They are a substantial high quality product that is 140mm (5-1/2”) high, with a feel that has never been achieved before without long hours of skilled work on the modellers workbench. The footprint of the base is 60mm x 15mm
£19.95

Must be ordered - delivery as soon as possible.
(Product Ref 116009)
Cookies are disabled.
To place an order please call 01453 377030
There are 6 sets of switches and 12 LEDs in each pack. The switches are standard 1/4? hole mount. The LEDs plug into the switches and are designed to be “push-fit” into your panel – all you have to do is use the correct drill size for the easiest control panel creation that you have ever had!
The use of bi-colour LEDs allows a light to be arranged on each route controlled by the switch such that the route set can be indicated by the green LEDs, while switching the other route indication to red. This provided a rapid visual reminder of any incorrectly set points along the planned route.
£24.95

Must be ordered - delivery as soon as possible.
(Product Ref 116022)
Cookies are disabled.
To place an order please call 01453 377030
Primarily designed for the Cobalt-SS motor, this pack makes distant or remote mounting of turnout motors a breeze, 12 lengths of Teflon tube and phosphor bronze wire plus 6 cranks, gold plated fixing pins and a pack of motor linkages give you all that you need to get it working.
£24.95

Must be ordered - delivery as soon as possible.
(Product Ref 116025)
Cookies are disabled.
To place an order please call 01453 377030
Pack of 5 Gaugemaster Seep Universal Solenoid Point Motors with Extension Rod GMC-PM10
£35.00

Must be ordered - delivery as soon as possible.
(Product Ref 112832)
Cookies are disabled.
To place an order please call 01453 377030
Have a question? Contact us
Wiring for layouts and electrical components can be found in the electrical section of our tools and hardware range.